INTERNATIONAL POLYMER PROCESSING

Enhancement of Injection Molding Consistency by Adjusting Velocity/Pressure Switching Time Based on Clamping Force

Mechanical and Thermal Properties of Teak Wood Flour/Starch Filled High Density Polyethylene Composites

Structural and Optical Characteristics of Laser Irradiated CdSe/PVA Nanocomposites

Study of Rheology and Plug Assist Thermoforming of Linear and Branched PP Homopolymer and Impact Copolymer

Study of Bonding Formation between the Filaments of PLA in FFF Process

Influence of Ultrasonic Transducer Structural Parameters on the Frictional Plasticizing Heat Generation of Polymer Particles

On Induced Properties and Self Heating during Free Blowing of PET Preform

Thermomechanical Degradation of Polyetherimide (PEI) by Friction-Based Joining and the Effects on Quasi-Static Mechanical Strength of Hybrid Joints

Damping, Thermal and Mechanical Analyses of Polycarbonate/Cerium Oxide Composites for Structural Applications

Optimization of Injection Stretch Blow Molding: Part I – Defining Part Thickness Profile

Effects of Cooling Ways on the Structure of Polypropylene Hollow Fiber Membranes Prepared by Stretching

Research on Influencing Factors of the Thermal Contact Resistance in Thin-Wall Injection Molding

Fill Factor Effects in Highly-Viscous Non-Isothermal Rubber Mixing Simulations

Identifying Melt Processing Conditions for a Polyacrylonitrile Copolymer Plasticized with Water, Acetonitrile and their Mixtures

Morphology and Isothermal Crystallization Kinetics of Polypropylene/Poly(ethylene-co-vinyl alcohol) Blends

Kinetic Analysis on Thermal Decomposition of Poly(lactic acid) Toughened by Calcium Sulfate Whiskers

Micro-Residual Stress Measurement in Nanocomposite Reinforced Polymers

Flame Retardancy Effects on Intumescent Coatings with Vinyl Acetate Copolymers

Study on Influence of Co-Injection Molding Process on Self-Reinforcing Characteristics of Self-Reinforced Polypropylene Composite via Visualization

Characterization of Anisotropic Properties of Hot Compacted Self-Reinforced Composites (SRCs) via Thermal Diffusivity Measurement

Effects of Zinc Borate on the Flame Retardancy Performance of Aluminum Diethylphosphinate in Polyamide-6 and its Composites

Rheology and Extrusion Foaming of Partially Crosslinked Thermoplastic Vulcanizates Silicone

Preparation and Characterization of Hydrophobic Flat Sheet Membranes Based on a Recycled Polymer

Mechanical and Fracture Peculiarities of Polypropylene-Based Functionally Graded Materials Manufactured via Injection Molding

The Effect of Ultraviolet Ageing on the Flame Retardancy, Thermal Stability and Mechanical Properties of LGFPP/IFR

Study of Melt Spinning Processing Conditions for a Polyacrylonitrile Copolymer with a Water/Ethanol Mixture as a Plasticizer

Theoretical and Experimental Studies on Tribological Behavior of Luffa Fiber Reinforced Polyester under the Influence of Surface Treatment

Synthesis of a Novel Ladder Poly(azomethine-ester) Based on PET Waste Bottles

Thermal, Tensile, Electrical, Dynamic Mechanical Thermal and Rheological Properties of Polyvinylidene Fluoride and Fluoroelastomer Composites Filled with Carbon Black

Influence of Post-Treatment Media on Morphological Changes in Transient Macromolecules of Polymeric Fibers

Enhancing Flame Retardancy, Thermal Stability, Physical and Mechanical Properties of Polyethylene Foam with Polyphosphate Modified Expandable Graphite and Ammonium Polyphosphate

Fabrication of Double-Sided Micro-Lens Array Using UV Injection Molding

Simulations of Heat Transfer in Thermoplastic Injection Molds Manufactured by Additive Techniques

Partially Filled Flow Simulation Using Meshfree Method for High Viscosity Fluid in Plastic Mixer

Three-Dimensional, Non-Isothermal Simulations of the Effect of Speed Ratio in Partially-Filled Rubber Mixing

The Influence of Mechanical Recycling on Properties in Injection Molding of Fiber-Reinforced Polypropylene

Influence of the Mold Temperature and Part Thickness on the Replication Quality and Molecular Orientation in Compression Injection Molding of Polystyrene

Preparation and Characterization of a Biocomposite Based on Cork Microparticles in Poly(β-hydroxybutyrate)-co-Poly(β-hydroxyvalerate) Matrix

A Closer Look at the Bonding Capacity of Thick Metal-Plastic Hybrids

UV Pre-Treatment for Polycarbonate for Bonding LSR in a Multi-Component Injection Molding Process

Processing LDS-Circuit Boards by Selective Laser Sintering

Could Alfa Fibers Substitute Glass Fibers in Composite Materials?

Effect of Annealing Temperature on PP Microporous Membranes Obtained by a Melt-Extrusion-Stretching Method

Influence of Rubber Ratio and Crosslinking Agent on Mechanical Properties, Crystallization and Rheological Behaviors of EPDM/PP Thermoplastic Elastomer

Influence of Process Parameters on the Morphologies of Micro-Injection Molded Polyformaldehyde Parts

Simulation-Based Approach for Probing Rheology-Processing-Structure Relationships in Foam Blow Molding

Preparation and Properties of Functionalized Lignin-Modified Polyvinyl Alcohol